The XS-05 uses the overseas utilities electrical power to regenerate a new power that not only has the correct voltage and frequency, but through various filters and levels of control, acts as a voltage regulator that eliminates surges and transients. A power factor corrected input (PFC) provides harmonic filtering on the input by removing voltage and current distortions that may be caused by the appliance. The XS-05 provides the appliance with a high quality, constant, and noise free electrical output of 120v~60 Hz – anywhere in the world.
An appliance intended for the USA is designed, manufactured and tested to operate in a 120v~60 Hz environment. As appliances have evolved in electrical sophistication and government efficiency standards have continuously become more stringent, engineers are forced to design each individual component, and the unit itself, to operate in the substantially more efficient 60 Hz.
Installing a step-down transformer to power a 120v~60 Hz designed appliance from a 220v~50 Hz grid will cause the appliance to operate at 50 Hz. At best – it functions but not properly. But most likely, the appliance will have a shortened product life, failed components and unforeseen damage resulting in catastrophic failure.
In other words, the XS-05 does not power the appliance like an installed transformer. It is an adapter that converts 50 Hz utility power, providing an appliance with the correct voltage and frequency of 120v~60 Hz that it was designed and tested for.
The XS-05 is a rugged full-featured device. Its specialized connecters provide for secure and safe installation. Its slim, lightweight design allows it to be mounted onto an appliance, or nearby via the included mounting plate.
XS-05 is a full-featured sine wave output regenerator that produces new, clean, and constant AC power; eliminating line noise and ensuring optimum performance. It is capable of providing 120v~60 Hz electricity for running a single household appliance (up to 600W).
Through sophisticated electronics, as well as input and output EMI and RFI filters, it produces continuous power at over 92% efficiency and with output Harmonic distortion below 3%. High levels of regulation ensure 120v~60 Hz output with fluctuations below ± 2% (typical less than 1%).
The XS-05 has sealed, solid-state electronics that protect against humidity and dust, ensuring reliability and a long product life.
Not only will electrical equipment perform better, but the XS-05 also acts as an advanced voltage regulator, which fully protects equipment against voltage irregularities such as under INPUT voltage as low as 180Vac and over voltage as high as 265Vac and provides an appliance with inrush surge protection of up to 150 Amps.
Audible alarms notify overload, short circuit and temperature.
The XS-05 meets International Standards. Even though this device would probably not be used in the USA, it also comes with UL and FCC approvals, giving the manufacturer/installer and the end user the confidence that their appliances, which meet these safety standards, are connecting to a device that is also meeting these safety standards.
- Frequency Converter
- Voltage Converter
- Sophisticated Voltage Regulator
- Surge Protection
- Short Circuit Protection
- Over-Current Protection
- Power Factor Correction (PFC)
- Thermal Protection
- High Efficiency
- Input EMI and RFI Filters
- Output EMI and RFI Filters
- Low Harmonic Distortion
- Sealed, Solid State Electronics
- Continuous Power
- Audible Alarms
- International Approvals
- Wall Mounting Kit
Wall Mount, (4) Input 3-pin Locking Connector Cord Type F, G, I, M
|Output Current-Amps @ 60Hz
||± 2% From Setpoint
||60Hz (Auto-Synchronized to Mains)
|Output Distortion (Resistive Load)
|Output Distortion (Reactive Load)
|Non-Linear Peak Current for 30 sec.
|Total Harmonic Distortion
||< 3% at 100% Linear Load
|Output EMI Filter
||150Khz - 30Mhz
|Output RFI Filter
||30Mhz - 1000Mhz
|Over Current Protection
||Over Load Alarm Level: 100% ~ 135%
(alarm after 1 minute delay, shutdown after 1 minute alarm)
Over Load Shutdown Level: 136%
(shutdown after 2 second delay)
||Pulsating Type, 40A Peak
Auto-Restart time: 30 seconds
|Maximum Continuous Load
|Maximum Peak Load
||46Hz ̴ 65Hz
||Full-Time EMI/RFI Filtering
|Input EMI Filter
|Input RFI Filter
||30Mhz - 1000Mhz
|Over Current Protection
Over Current Protector
||180Vac ̴ 265Vac
||Over Load Alarm:
1 beep every 2 seconds
Every other 2 seconds, 32 beeps in 2 seconds
|Inrush Surge Capacity
|Voltage Interruption Ride Through
|Environmental and Safety
||Up to 2000 Meters:
0° to 45°C
(32°F to 113°F)
||-15°C to 60°C
(5°F to 140°F)
||5 – 95% Non-Condensing
||0 ~ 3000 Meters
|External Cooling Fan Control
|35.00 × 27.00 × 6.00 cm
13.78 × 10.63 × 2.36 in
|Net Product Weight
|51.00 x 47.00 x 20.00 cm
20.08 x 18.50 x 7.87 in
||2 Years, Full Replacement
|Quality Control Standard
||UL-ULus (CCN: QQFU/7) Power Units Other Than Class 2,
UL 1012, Seven Edition, October 14, 2008
UL-cUL: CAN/CSA-C22.2 No. 107.1-01, September, 2001
DEMKO-CB IEC60950-1:2005+A1:2009+A2:2013 (Ed. 2.2)
TUV/SUD-CB IEC 60335-1:2010+A1:2013 (Ed. 5.1)
FCC Part 15: subpart B
- UL-ULus (CCN: QQFU/7) Power Units Other Than Class 2,
- UL 1012, Seven Edition, October 14, 2008
- UL-cUL: CAN/CSA-C22.2 No. 107.1-01, September, 2001
- DEMKO-CB IEC60950-1:2005+A1:2009+A2:2013 (Ed. 2.2)
- TUV/SUD-CB IEC 60335-1:2010+A1:2013 (Ed. 5.1)
- FCC Part 15: subpart B
- EMC 2004/108/EC
- PowerXchangers meet IEC Standard 60335-1 and are considered a critical component of an appliance when used with another appliance that also meets the same IEC 60335-1 International Safety Standard
Click here to download product brochure (A new browser window will be opened).